ita flag big  eng flag big  facebook logo linkedin logo linkedin logo

16-6-2015 A New Yacht Born-Aluaka-Stadtship 54 Ac

After 13 months working, 300 hours driving, 5000 hours design, 3000 hours interior workingn, 3000 system and hardware working, with 15 days delay for mast builder delay, thank to Cantiere Zuanelli, Autostraporti Adbon Pedretti with 5 m height truck transport, ALUAKA, touch the water in the Harbour of Chioggia (Venice), Darsena Le Saline.

It took 5 hours to launch, preare and install the mast, boom and the solar panel arch under a 30°c sun already tested in the Zuanelli Yard.

Finally we get a bert and a nice rain drop all the night.It seams Ushuaia. Flag is on the pole and the Pantaenisu Insurance is ready.

Next month will be busy for sea trial.

On the truck of Abdon Pedretti Autotrasporti ready to go

At the dock with heavy rain.

Perfectly on the water line

On day 2 we have installed the Scantrust self leveling pole, wind gen, rope spools/drums, tune the mast and the Facnor furlers

Bimini and side covers, pilot house window covers set up!


Time to go home, see you next week.




Almost ready for the first “splash” of Aluaka, the Stadtship 54Ac. The carpenters have done a good job, not always easy. The major difficult they had, was to think how to make all the panels easy to disassembly and to bend the ceiling of the round shaped pilot house.

Most of the visitors on board don’t understand that the floor is made in rubber  with wood pattern. We say that is only rubber nobody believe us. Nice!

We had finish the plumbing with John Guest and we had fix all the small leaks and finally we decide to install a water heater, no Reflex and no hydronic webasto. It’s always possible, but for now, we would like to sail asap and kiss.

The Cnc Treadmaster has been the perfect choice to speed up the job for the antislip on deck. We used epoxy West System to glue it. A ncie job done in 5 days

We had the bad surprise that there was a missing weld on the day tank , the only one not tested (the Murphy ‘s law) and Milan our proud welder fix it. Hope no more surprise like this.

TheTecnosystem upholsterer  start  to make the template using a film for all the berth and the bimini, in one month I will have all the material, including the windscreen mesh to keep heat low under the pilot house glass when in the Med and Caribbean.

The Ce certificate is almost ready and finally we find the way to weld the keel in-house and transport the boat with 5 m height from the street, thank to Abdon Pedretti. The yard in Chioggia (venice) has been booked for June. We don’t know now for the holiday, sailing long the Croatian coast or straight to grece after the final boat tuning.

We are only waiting for the mast from Sparcraft ordered the 30th Oct…Hope will arrive!

(Last new the ETA was 16 April now shifted to the 4th of May…May be for the 10th we got the mast! Hope all Right.

The sails are on the way, we have just ordered the Ultra GLF  antiwtsit cable for the Asy and the Code.


A lot of changes in CN Valle Scrivia Srl, Some new people and I’m just back from Spectra Training Class in San Francisco.

We still busy with a lot of survey in used market and some new job on desk.


The cockpit with wood batten seat to stay dry and ventilated good in cold and hot climate


The pilt house bimini made in mesh will keep low the temperature on the glasees.The mesh will offer less wind resistance.

Please note the wood strip to make all the tread master panels at the same distance


Gluing the Treadmaster: check the panel size and space beewten, then grind the deck, set the panels and lay the tape leaving 1-2mm space around the treadmaster. Clena the panel, grind again the aluminium more gentle, cleaning with solvent then apply on both surface the resin. Stich them, adjust the panle in the tape template, then press it or roll it to debuble little bit of air, then make the edge smooth. This job need two persons.

The final job

The final Job (note Aka on the background)


A sharp view of the iteripor, see the fake wood floor. All the floor panels are insulated


The engine room




Happy SAILING FOR THE 2015 - I guess you a good trade wind, a new set of sails and a new place where stay safely at anchor


1st DECEMBER 2014



I’m the worst blogger. I didn’t update the news page from this summer, but there is a reason. We work and push the business very hard.

Aluaka has been spray with about 75mm 40Kg/mc foam on the side and 50mm on deck. The pilot house has been done with Armaflex 30mm. The boat has become quite and colder during summer and warmer now. We had paint the superstructure only. It will be the only paint. We choose to make the pilot house in red, just to obtain a better visibility from others. Then we install some hardware like the anchor winch, the G70 Aqua 7 from Maggi 100m-diameter 10mm chain and the 2500W-24V anchor winch. The carpenters had start working last week of Aguste and they start assembly the panel quickly. The wood supplier  is Belloti and the wood finishing is ALPI, so we don’t lose time in varnish. At the moment we are at 70% of the interior. We spend a lot of time searching a good floor. On our past boat we had a nice rubber, cork finished. Now we choose a laminated wood, very hard, able to support scratches from shoes.

We define the mast with Sparcraft G&G rigging with Facnor continuous furling lines for asymmetrical spinnaker, code Zero, Jib,Staysail and FB mainsail 4 reefs.

We start to install the electronics NKE autopilot with true wind option, the same used on Class 40 and Imoca 60 and B&G Triton display with forward scan. After year of good relationship we left Raymarine.

Last week our friend Milan finish to weld some details as the ropes spool, 2 x 150m floating nylon ropes 24mm and 2 x 150m 12mm dynema. We are learning how to splice from our friend Gianka.

We also pass a lot of tinned cables from Anchor and Spencer Marine arriving sometime from Asap supplier.

We install the two Lavac toilet, one manual and one electrical +manual.

We start to play with the treadmaster that is now under CNC. We will glued on deck after using an eccentric tool to sand the plate, then we will use West System to glued it. We made a sample and we kept in the oven and in the deep fridge passing from -30°c to +60°c to see how reacts.

We installed the seals in silicone at 0.4Kg/mc density on all lokers.

  • 003
  • 005
  • 007
  • 011
  • 012
  • 017
  • 042
  • 052
  • 056
  • 057
  • 207
  • 304
  • DSC00753Small

Simple Image Gallery Extended


The Gianka's boat is totally different from Aluaka and is very nice too. Two different beauties!

The bottom are quite the same, Aka 56 has a deeper V in front and has a reverse transom. The keel is moderate longer. The engine is 75hp with sail drive, and there are “only” 4  WT bulkhead.

The Pilot House has several small windows with 6+7+6mm double glass.


AKA 56



We wish a windy summer to all our customer around the 7 Oceans.

The Darwin 86-3 is now ready for the holiday. This big motoryacht cruise at 12Kn with the two Man D2876 331kW @1800rpm. The boat is very quite with no vibration and a average noise of 55-60dB, very low, thanks to the superior insulation.It took a month to get the boat ready and the yard spend a lot of time searching good supplier for the canvas and last extra equipment. Probably the boat will be in Cannes Boat Show.

Darwin 86-3

We have big  progress with the K&M Bestevaer 56 in Holland. The hull has been turned upright 2nd of July.
We had check the welding and assembly for the third time and visited the yard again and his beautiful yachts. We will see again the BV56 in the middle of September when will be almost finished with engine and hull grinded ready for delivery.
Here the owner photos blog where you can see our rendering and interior proposal

Bestevaer 56

The works of the Stadtship 54Ac are on progress in Zuanelli Shipyard, and after the summer the interior layout will take shape, finally we decide to use Alpikord laminates for superior resistance to scratches and sun. the wood panel will arrive already industrial varnished, so no loose of time during the assembly. The Antal deck gear is now installed, the electrical system is now at the 75% with all the  ducts and tinned cables by Ancor Marine. The Aqua 7 Maggi chain will shortly arrive and combined to the Rocna 55Kg will give us superior ground tackle capability. The bimini and all the metal work are finished. We had start to foam 100mm insulation Froth Pack 45Kg/cdm, except for the pilot house, where we prefer use Armaflex 35mm, to do a nicer and uniform job (but how long to get all the pieces in shape).We hope that the engine room insulation with Armasound will be faster!

Stadtship 54Ac

Patimar, our old proud boat, is back in the water from 1st of June and will sail in Greek Water with the new owner. I had to help him to make first sea trial, maneuvering, anchoring  and start the watermaker. It’s a little bit strange sailing her for the last time after 12 year, but we were lucky with a 10-12Kn wind we immediately reach 6.5kn

There’s a lot on interest in Aluminum yacht specially after several accident of yachts that loose the keel. A lot questions regarding shipyard and yachts like Boreal 44 or 47, Futuna, sistership of Seal (Ed Joy), Ovni, Atlantis Dujardin, Koopmans, Garcia. The questions are regarding the stability, the behavior, the insulation and sailing capacity.

On our desk there are some structural project,one for ar new composite 40' boat. The survey of Italia 998 Matteo Polli Yacht Design is almost finished, the boat will be ready end of July.We will see.


More Articles ...

AVVISO: Questo sito utilizza cookies; continuando a navigare sul nostro sito, accetti implicitamente l'utilizzo dei cookies